Fixtures we install in kitchens, baths and laundry rooms
The usual list is toilets, bathroom and kitchen faucets, sinks, tubs, shower valves and trim, dishwasher supply and drain hookups, ice maker lines, and washing machine boxes. Each one needs a shutoff you can reach, a trap that holds water and a drain that slopes.
A kitchen sink with a disposal adds an electrical outlet, a dishwasher air gap or high loop, and a continuous waste line. If the disposal is the only thing changing, garbage disposal repair and replacement covers the swap.
Remodel, addition or new build: how the plumbing differs
The same fixture takes a different path depending on what is around it. Match your project to the row below before you ask for pricing.
| Project | What the plumbing involves | Common surprise |
|---|---|---|
| Fixture swap | New faucet, toilet or vanity on existing lines and valves | A stop valve that will not close or a supply line that cracks |
| Bathroom or kitchen remodel | Moving a drain or valve, new shower valve, re-venting | Old pipe that does not match the new fittings |
| Room addition | New branch lines tied into the main supply and drain | Not enough pressure or drain capacity for added fixtures |
| New construction | Underground drains, rough-in, top-out, trim and testing | Inspection timing that holds up the next trade |
Rough-in, top-out and trim: the stages of new plumbing
Rough-in comes first. Drains and vents go into the slab or floor framing, and supply lines are run through the studs before any drywall. The inspector looks at those pipes while they are still open.
Top-out follows, with vent stacks through the roof framing and the lines pressure tested. Trim is the last visit, when toilets, faucets and valves are set on finished walls.
Underground work in sandy soil
Florida's soils in the north and central part of the state are typically very sandy, according to University of Florida extension. Sandy trench walls slump, so an excavation near a new drain needs shoring or a shallow slope. Call 811 at least two full business days before anyone digs, so buried utilities are marked.
Decisions to make before the rough-in
Changes after the walls close cost far more than changes on paper.
- Exact fixture models, since rough-in dimensions come from the spec sheet and the standard toilet rough-in is 12 inches from the wall.
- Where the shutoff valves and cleanouts go, and who needs to reach them.
- Whether you want a shower valve with a thermostatic or pressure-balancing cartridge.
- Outdoor hose bib and laundry box locations.
- Water heater location, plus the vent, gas or electric supply it needs.
- A written scope that names who pays for patching drywall and tile.
Adding a bathroom or moving a fixture
Drains work by gravity, so a new bathroom has to reach the main drain with a slope of about 1/4 inch per foot. That is easy over a crawlspace or open framing and harder on a slab, where the concrete may need to be cut and patched. A toilet needs a 3 inch drain, and every fixture needs a vent so the trap does not siphon dry.
Hot water is the other limit. A new bathroom group on a 40 gallon tank can leave the last shower cold, so look at the heater too, and water heater installation covers sizing and a larger tank or tankless unit.
Permits and inspections: Altamonte Springs and nearby
In Altamonte Springs, the Building and Fire Safety Department at (407) 571-8446 issues the permits. The city lists a plumbing permit type for work whose plans were pre-reviewed under a building permit, and a stand-alone plumbing permit for work that needs no plans. Ask which fits your job before you buy materials.
Florida's plumbing code is the Florida Building Code, Plumbing, 8th Edition (2023), which is based on the 2021 International Plumbing Code. Lake Mary states that electrical, plumbing, mechanical or gas work requires a permit with no exceptions, and invites homeowners to ask first when they are unsure. That is a good habit in any city.
What drives the price of plumbing installation
Fixtures are the easy part. Walls, slabs and distance decide most of the cost.
| Job | Typical ballpark | What changes it |
|---|---|---|
| Toilet or faucet install | $150 to $450 | Fixture type and shutoff condition |
| Shower valve and trim, existing wall | $500 to $1,500 | Wall access and valve brand |
| New bathroom rough-in | $2,500 to $7,500 | Slab or crawlspace, distance to the main |
- Access to pipeOpen framing is cheap to plumb. Finished ceilings and slab floors add cutting and repair.
- Distance from supply and drainEvery extra foot of pipe adds material and labor, and a long drain run needs more fall.
- Fixture gradeA basic toilet and a wall-hung model with an in-wall carrier are very different installs.
- Permit and inspectionPermit fees and inspection scheduling are part of the schedule even when the work itself is quick.
Treat these as typical ballparks that change with the job. We state the price clearly before work starts, and you can compare it to any other quote line by line.
Neighborhoods, condos and what to expect
Altamonte Springs has 137 single-family subdivisions and 97 multifamily communities. Single-family remodels usually mean opening walls inside your own property lines. Condos and apartments often need written approval from an association before the water goes off, so ask early about shutoff windows and allowed work hours.
Bring photos of the existing shutoffs, the water heater and the panel nearest the work. A technician who sees the layout in advance can plan the route for new pipe and bring the right fittings.
Limits and urgent calls
We install plumbing. A new circuit for a disposal or a tankless heater is an electrician's job, and your gas utility handles anything on its side of the meter. If you smell gas, leave, call 911, then call the gas utility from outside.
If new or old plumbing fails at night, the 24/7 line at (407) 964-8940 takes the call and we dispatch same-day when the schedule allows.
Plumbing installation questions
Often yes for anything beyond a like-for-like fixture swap, but the exact rule depends on the job. Ask the City Building and Fire Safety Department at (407) 571-8446, since we could not confirm every case from the city's pages.
Usually, yes. Check that it matches the hole count, drain size and rough-in, and keep the spec sheet. Some fixtures ship without the parts a code-compliant install needs, so extra fittings may add to the price.
A single bathroom is often a day or two of plumbing work, followed by a rough inspection. Slab cutting, a long drain run or unusual venting adds time.
Yes. We handle underground drains, rough-in, top-out and trim, and we coordinate around inspections so framing and drywall are not held up.
Adapters and transition fittings handle most mismatches. If old galvanized or brittle pipe breaks when touched, the technician will tell you before replacing a longer section.